How do I get rid of DSTV error codes?

How do I get rid of DSTV error codes?

If the Error code you see on your T.V set is any of these, just relax and follow this step to get it cleared.

1. Go to www.DSTV.com.
2. Select the type of Error code that you see on your T.V set, enter your smart card / Serial No, and solve the Captcha.
3. Click “Reset Device”

How do I get rid of e18 4 error on DSTV?

How do I clear e18 error on DStv? Just connect whatever has been disconnected, wait for fifteen minutes, and enjoy the services. Re-insert the correct card, arrow facing the decoder and the chip facing downwards and then reboot the decoder. Make sure the card is clean.

How do I get rid of e48 32 error on DSTV?

The error is easily fixed by turning off the TV and leaving it off for a few seconds, and then turning it back on again. The main cause of the e48-32 error is the accumulated dust on the Dstv card, which causes the card to overheat and activate the unused component, which then deactivates after a while.

How do I clear DStv errors after payment?

Check to ensure that your card is inserted correctly. To clear the E16 error in both DSTV and GOtv, you need to send a text message. For DSTV, text the word ‘RESET’ followed by your card number to 22688. In the case of GOtv, send a text message with the word ‘RESET’ followed by your ICU number to 22688.

How do I fix E19 4 on DSTV?

E19-4 Subscription Status Expired

1. Leave the decoder turned on and the information on the smart card will updated to restore all of the activated services. The decoder usually recovers within a couple of hours.
2. Reactivate the smart card by entering the smart card details here.

How do I fIX E48-32 searching signal?

fIX DSTV E48-32 ERROR- LUBSAT TECHICIANS

1. Re check cabling coming from dish to the decoder.
2. Check / try restarting your decoder.
3. Re align satellite dish, to gain more signal levels, cause might be you are receiving low signal.
4. Communal dish check your in house cabling, other wise call us.

What does 503 mean?

Service Unavailable Error
A 503 Service Unavailable Error is an HTTP response status code that indicates your web server operates properly, but it can’t handle a request at the moment. Since it’s just a generic error message, it’s difficult to pinpoint the issue’s exact cause.

What is the server 503?

The HyperText Transfer Protocol (HTTP) 503 Service Unavailable server error response code indicates that the server is not ready to handle the request. This response should be used for temporary conditions and the Retry-After HTTP header should, if possible, contain the estimated time for the recovery of the service.

How do I clear the error code on my decoder?

If there is no response on the hotline, you can clear the error yourself by dialing *120*68584# and following the instructions on your smartphone screen. If this error lasts for more than a few hours, you may call the Multichoice number at 012 422 2222 to reset your decoder.

What to do if my DStv decoder is not working?

The DSTV Flash memory is corrupted. Get in contact with one of our local DST installers to send someone out to check your DSTV Decoder. Switch the decoder on by pressing on the power button on the remote control. This could be any error, but it is usually due to no signal. Reset your decoder by disconnecting and reconnecting the main power supply.

How to reset the decoder to factory default settings?

1 Press the reset button combination 2 Wait for DL to appear 3 Press and hold V- and Play buttons simultaneously 4 Keep holding in the buttons until lights flash on the front panel of the decoder followed with MSK ERASE 5 Decoder will display scan More

How to decode the Code of your TV?

Below are the steps to be followed for the different decoders: Once it appears – press and hold P+ and V- simultaneously until you see flashing lights followed by the message – DONE Remove the power cable and put it back while holding down the +P button until you see 4 dots or a word CODE on the TV screen. Put the code as -P +P +P -P (0110).