What is data mover in EMC VNX?

A Virtual Data Mover (VDM) is an EMC® VNX™ software feature that enables the grouping of Common Internet File Systems (CIFS) and/or Network File Systems (NFS) environments and servers into virtual containers. VDMs contain the data needed to support one or more CIFS and/or NFS servers and their file systems.

What is data mover enclosure?

Data Mover Enclosure – Blade Enclosure – This enclosure houses the data movers for file and unified VNX arrays. Think of a data mover like a linux system which has SCSI drives in it, it then takes those drives and formats them with a file system and presents them out one or more protocols for client machines to access.

What is EMC Control Station?

Control Station are 1U in size and provide management functions to the file-side components (referred to as Blades or Data Movers). The CS is responsible for Blade failover. To provide HA Control Station might be configured with a matching secondary CS.

How do you use data mover in PeopleSoft?

Use the development environment. Create and run PeopleSoft Data Mover scripts. Use the Database Setup utility. Use the PeopleSoft Data Mover command-line interface….To run a script:

Select File, Open.
Select one of the following types of script to run. PeopleSoft Data Mover files (.
Select File, Run.

How do I shutdown my EMC VNX 5400?

EMC VNXe – Shutdown Procedure

From Unisphere, select Settings > Service System.
Enter the Service password to access the Service System page.
Under Service Actions, select Shut Down System.
Click Execute service action to shut down the storage processors (SPs).
In the Service Confirmation dialog box, click OK.

What is the difference between VNX and unity?

Dell EMC Unity is the improved version of EMC VNX. It has all the features in VNX with better performance. NetApp all flash is faster and more expensive. It performs better with Citrix systems and VDI solutions.

How do I access EMC VNX?

You can go via: the SP’s management port: http:// IP address>:9519; the SP’s service port: https://128.221.1.250:9519 (SP A) or https://128.221.1.251:9519 (SP B); and. the SP’s serial port: https://192.168.1.1:9519 (this assumes you’re connected via serial already – more on that below).

How do I access Vnx command line?

Instructions

Log into Unisphere.
Select the System tab.
Go to Control Station CLI at the bottom right pane.
Select Run Command right below that.
The command page opens for entering commands. Article Properties. Affected Product.

How do I create an NFS share in EMC VNX?

Steps to Create NFS Export:

Choose Data Mover = server_2.
File system = Select the filesystem from dropdown list.
Path = Leave Path at default value (it will normally match the name of the Export)
Read/Write Hosts = 10.87.05.42:10.97.15.45:10.46.71.37:10.16.71.35.

What is datadata mover in VNX?

Data Mover is a hardware component of VNX for File. It reads the data from back-end storage by UltraFlex I/O technology to provide the data access. It supports NFS, CIFS and pNFS protocols. The component has scalability and redundancy.

How many DPES does the vnx5300 support?

The VNX5300 platform supports two types of DPEs and DAEs; a 15 drive 3.5-inch disk 3U enclosure and a 25 drive 2.5-inch disk 2U enclosure. Expansion of up to seven 3U DAEs (a maximum of 120 3.5-inch disk drives) or up to four 2U DAEs (a maximum of 125 2.5-inch disk drives) is supported.

What are the best storage options for VNX?

• Flash drive – Flash drives provide extremely high performance and consume very little power. These drives enable a VNX to provide an Extreme Performance level of storage for critical workloads. Flash drives can also be used to extend the array’s cache using FAST Cache technology.

What is a VNX flash drive?

These drives enable a VNX to provide an Extreme Performance level of storage for critical workloads. Flash drives can also be used to extend the array’s cache using FAST Cache technology. • Logical unit number (LUN)—Identifying number of a SCSI or iSCSI object that processes SCSI commands.