How do you use a U bolt clamp?
How to Install a U-Bolt
- Place the U-bolt around the pole or pipe.
- Slide the U-bolt clamp over the part you are attaching.
- Place a washer on each of the threaded U-bolt ends.
- Turn the first bolt by hand in a clockwise direction until snug.
- Tighten the bolts with the wrench.
How do you install U clamps?
How to Install a U-Bolt
- Step 1: Remove the Nuts. The U-bolt will probably come with nuts attached to its threads.
- Step 2: Position the U-Bolt. Place the U-bolt around the object you’re attaching to the beam or support.
- Step 3: Examine Your Holes.
- Step 4: Thread the Bolt Through.
- Step 5: Fasten the Nuts.
Which way do cable clamps go?
The proper way to use wire rope clips can be remembered this way: “Never saddle a dead horse.” The saddle of the clip is the piece that fits into the U bolt. The dead-end of a wire rope is the end of the eye that contains the cut side.
What is the proper way to attach the U bolts to the wire rope?
The correct way to attach U-Bolts is shown at the top; the “U” section is in contact with the dead end of the rope and is clear of the thimble.
What do you use U bolts for?
U-bolts have primarily been used to support pipework, pipes through which fluids and gasses pass. As such, U-bolts were measured using pipe-work engineering speak. A U-bolt would be described by the size of pipe it was supporting. U-bolts are also used to hold ropes together.
What are square U bolts used for?
Square U Bolts are designed to fix an item to a box section structure or trunking, or used for clamping square or rectangular items. Typically, they find themselves in use within the suspension of metal channels and duct work – but can also be embedded in concrete as anchor bolts or used to secure heavy equipment.
How tight should bolts be?
Tighten all U-Bolts until they are snug only. Tighten in the sequence shown to approximately 1/3 of recommended torque.
When U-bolt wire rope clips are used to form eyes?
When U-bolt wire rope clips are used to form eyes, Table H-2 shall be used to determine the number and spacing of clips. When used for eye splices, the U-bolt shall be applied so that the “U” section is in contact with the dead end of the rope.
Which side of a wire cable should you install the saddle on when using cable clips clamps?
There are two sides of a U-Bolt style wire rope clip: the saddle and the U-Bolt. When securing a wire rope eye, it is important to place the clip on the correct end of the rope. The saddle of the clip rests on the live end of the rope, while the U-bolt is to rest on the dead end of the rope.
How far apart are cable clips?
Clips are usually spaced about six wire rope diameters apart to give adequate holding power. They should be tightened before the rope is placed under tension. After the load is placed on the rope, tighten the clips again to take care of any lessening in rope diameter caused by tension of the load.
How to install U-bolt clips correctly?
Follow the steps below to install u-bolt clips correctly: STEP 1: Apply the first cable clip one base width from the dead end of the wire rope. The U-part goes over the dead end, while the live end rests in the clip saddle. Tighten the nuts evenly to the recommended torque. STEP 2: Apply the second clip as close to the loop as possible.
How do you use a you bolt clamp?
A U-bolt consists of two threaded ends that fit into two holes on a matching clamp. Two bolts hold the clamp into place. A properly sized U-bolt will securely fasten an object to a post or pole. You only need a few basic tools to install U-bolts. Place the U-bolt around the pole or pipe.
Can I use U-bolt wire rope clips to secure brackets?
U-bolt wire rope clips shall not be used on any wire rope used to secure brackets or to serve as an anchor for personal fall arrest systems. The preamble to §1926.452 (x) (9) in the August 30, 1996, Federal Register states:
How do I apply the cable clips?
STEP 1: Apply the first cable clip one base width from the dead end of the wire rope. The U-part goes over the dead end, while the live end rests in the clip saddle. Tighten the nuts evenly to the recommended torque. STEP 2: Apply the second clip as close to the loop as possible. U-part is over the dead end. Turn nuts firmly but do not tighten.