Why is my DIRECTV remote not working RC73?

To reset the RC73 remote: -Press and hold mute and select until the light blinks. -After releasing mute and select, type the numbers “9, 8, 1” in that order. -You should see the light blink again on the remote after typing the above 3 numbers.

How do I program my RC73 DIRECTV remote to my TV?

Just follow these steps:

Point the remote at your Genie DVR.
Press and hold the Mute and Enter buttons.
Your TV will display “Appling IR/RF setup.”
Turn on the DirecTV Ready TV.
Hold down the Mute and Select button.
Enter the manufacturer code for your TV.
Your remote should now be paired and ready to go.

How do I reset my RC73 DIRECTV remote?

Just hold down Mute and Enter (Not Select) button until you see lights flashing on the remote. It paired right away with my DirecTV receiver.

Why is my remote not connecting to my TV?

There are a number of reasons why your remote may not be working. The most common are physical damage, battery issues, pairing issues, or issues with the infrared sensor on the remote or TV.

How do I reprogram my directv remote to my receiver?

Program remote for an HD DVR or HD receiver

Press MENU on your remote.
Select Settings > Remote Control > Program Remote.
Choose the device (TV, audio, DVD) you wish to program.
Follow the on-screen prompts to complete programming.

How do I program my directv remote RC73 to my Onn TV?

DIRECTVhelp

Press MENUE on your remote.
Select Settings, Remote Control, Program Remote.
Choose the device (TV, audio, DVD) you wish to program.
Follow the on-screen prompts to complete programming.

How do you reprogram a keyless remote?

How to program a key fob

Replace the batteries inside the key fobs.
Get inside the car.
Turn on the ignition.
Press the lock button on the remote key.
Listen for a Lock Sound.
Programming additional remotes.
Turn off the ignition.
Step out from your car and test the result.

How do I program my directv remote to my Onn TV?

Step 1: Press and hold “MUTE” and “SELECT” at the same time until the green light flashes twice. Step 2: Type in the 5-digit code for your brand. After entering the first digit, wait 1-2 seconds until the green light flashes, then type in the remaining 4 digits.

How to reprogram DirecTV remote rc73?

Press select and then the mute button – you will see a green LED light flash twice on the remote

Dial the following number,“961” and then press the channel button UP – you will be able to change your channels on the TV

Press volume button Up and Down – Program Remote option pops up

Press the Select button to program remote

Press Enter and Mute Button for approximately a hundred 100 seconds or 2 minutes

Your DIRECTV Remote RC73 has been successfully set up

RF set up page pops us

Next step is to program your remote to control TV and audio

Enter Program TV

Locate the Brand of TV that you have i.e. Samsung and model number

Press the It Worked if it is working perfectly – otherwise try again

You are DONE!

How do you program a RCA Universal Remote?

Press and “HOLD” CODE SEARCH. Press and release the TV or VCR button you want to set up. When the selected device button blinks go to the next step. Next enter the 3 digit code from the TV, VCR or Cable Box remote code list. Release CODE SEARCH. With the device on press VOLUME UP to see if the tv responds.

How to program a RCA Universal Remote?

First you need to “Turn The Device On”

Press the “TV” on your “RCA universal remote”

Now press and hold the “Setup button” of the Universal Remote until it shows the “Light Flash” (It means it is in “Learning mode”)

Finally enter the “Keycode” which you collected from the programing guide (Instructions Booklet)

Once you’ve done this procedure,just “point your remote at the TV” and then “Press And Hold The Power” button

You can release the “Power Button” whenever the screen switches off

How to program a direct TV remote?

Program a DIRECTV universal remote for an HD DVR or HD receiver Press Menu on your DIRECTV remote. On the on-screen menu, select Parental Favs & Setup > System Setup > Remote or Remote Control > Program Remote. Select the device (DVD/Blu-ray player, DVR, gaming console, soundbar, TV, etc.) that you want the remote to control.