How much does it cost to lacquer a guitar?

So, How Much Does it Cost to Refinish a Guitar? A solid color finish will start at around $200, which goes up as you add custom colors and designs. Varnish and Lacquer can probably cost you around $300-400 just for the finish itself.

How many coats lacquer acoustic guitar?

An easy answer to the question would be that there is only one coat, since subsequent layers melt into and fuse with previous layers when they are sprayed. I do have an approximate count of the number of times I point my spray gun at the guitar, so I could tell people that there are 15 to 20 coats of lacquer.

How many layers of lacquer are applied to the guitar?

I’ve done some nitro refinishing on a couple of guitars, using both spray and brush ( yes, you read that right,,brush). The short answer is that it will depend how absorbent your wood is, but usually 6-8 coats is enough.

How long does cellulose take to harden?

Normally a high pressure spray gun is used at around 45psi. In the right conditions the paint should be fully cured in about 12 hours, (leave overnight).

Can you brush on nitrocellulose lacquer?

brushing is not the best way to apply lacquer you will feel it grabing pretty quickly , there is a brushing lacquer but it isn’t great for guitars. If you mask the area the you don’t want over spray you will be better off than brushing.

Does refinishing a guitar affect its value?

Refinish is NOT good to the value of the guitar, desk or chair, etc. It generally just kills the worth of the piece since the originality is gone. In some instances, some restoration work greatly enhances the value of the item, such as a restored automobile.

How much lacquer do I need?

Typically, if we are using spray applicators, 6-7 coats should be fine. And if we’re using a brush, then 3-4 coats is alright.

How long do I wait between coats of lacquer?

Question: How long should you wait between coats of lacquer? Answer: A standard of two can coatings is advised in one day. Yes, the lacquer may dry off only a few hours after application.

What causes lacquer to orange peel?

Orange peel is the most universal defect in a sprayed finish. The most common cause of orange peel is an imbalance between the viscosity of the finish and the amount of air atomizing the liquid as it exits the gun. The thicker the liquid, the more air that is required; the thinner, the less air needed.

How long can I leave cellulose between coats?

15-20mins
Applying Cellulose Colour Normally 3-4 coats are applied, allowing 15-20mins between coats. If any imperfections appear between coats these can be de-nibbed using an abrasive paper Grit P1200 or finer.

Can you lacquer over cellulose paint?

Cellulose paint still has a few advantages over some of the modern automotive paints, mainly that it is easy to apply and if you make a mistake it can be rectified straight away, the down side is you have to cut and polish all cellulose paint to get a good acceptable gloss finish or alternatively you can apply a couple …

What kind of lacquer do you use on a guitar?

Produces a beautiful traditional nitrocellulose lacquer finish, without elaborate spray equipment. ColorTone® Clear Aerosol Guitar Lacquer is formulated especially for musical instruments. Fast-drying and resistant to alcohol and water, it produces a hard, durable finish that enhances the beauty of the wood.

What is color tone stain for guitars?

ColorTone liquid stains are lightfast metal-complex dyes that can be mixed for practically any desired intensity. Unlike off-the-shelf hardware store stains, they’re formulated for guitar finishing. These concentrated grain-enhancing stains are economical; a little goes a long way.

What finishes can I mix Colortone stains with?

For applying transparent color-tinted coats, ColorTone stains can be mixed directly into virtually any finish: nitrocellulose lacquer, shellac, waterbase finishes, and catalyzed varnishes or lacquers.

What are Colortone liquid stains?