What size spray tip should I use?
A basic rule of thumb is to use small tip sizes (such as 0.009in, 0.011in, 0.013in) for thin / low viscosity materials such as stains & lacquers, medium tip size (such as 0.015″, 0.017″, 0.019″) for acrylic latex / enamel / emulsion / primer etc., then for heavier viscosity coatings use large orifice sizes (such as …
What is a 515 spray tip used for?
The reversible RAC IV SwitchTips are the most widely used tip for spraying a variety of coatings from lacquers to exterior paints. Use the Reverse-A-Clean (RAC) feature to quickly clear tip clogs by simply twisting the tip and spraying in the reverse position.
What is a 213 spray tip used for?
The 213 SwitchTip has a 0.013 inch orifice and produces a 4 to 6 inch fan. Reverse the SwitchTip to easily clear clogs. Used for residential, commerical or industrial applicaitions. Best used with materials ranging from lacquers, latex paints and mastics.
What is a 312 spray tip used for?
Spray at up to 50% lower pressure with the Reverse-A-Clean (RAC) 312 Fine Finish Low Pressure (FF LP) RAC X SwitchTip. This fine finish tip produces a 6 to 8 inch fan pattern and a 0.012 inch orifice. Reverse the SwitchTip to easily clear clogs.
What is a 210 spray tip used for?
Fine finish spray tips are used for cabinetry, furniture and interior trim work (for a smooth fine finish) example Graco FF LP spray tips: 210 or 310. Low pressure tips are used primarily for spraying with pressures between 55 to 76 bar (800 to 1100 psi).
What is a 417 spray tip used for?
Achieve greater control and less overspray on different surfaces with a wide range of coatings, from stains to exterior paints. 8 inch spray pattern ideal for larger surfaces such as interior or exterior walls.
What is a 211 spray tip used for?
The 211 spray tip is used to work with light lacquers and spray more accurately. For example, to paint beams and window frames. To paint larger surfaces, such as ceilings or tables, it would be more appropriate to use a 411 spray tip with lacquers or paints / interior materials.
What is a 413 spray tip used for?
The Reverse-A-Clean (RAC) 413 RAC IV SwitchTip is designed for narrow surfaces and thinner materials like stains and polyurethanes. The 413 SwitchTip has a 0.013 inch orifice and produces an 8 to 10 inch fan. Reverse the SwitchTip to easily clear clogs.
What is a .017 spray tip?
017 inch Max. This means you can use any tip that ends in 17 or lower. C: Kind of material you are spraying ( Example latex primer, or oil base stain. ) Thinner materials like oil based stains don’t need a large orifice to spray, while thicker material like latex ceiling paint will clog a smaller orifice.
What is a 315 spray tip used for?
The 315 tip is ideal for fence picket priming and painting. The 6” fan pattern minimizes overspray when spraying pickets.
What is a 215 spray tip used for?
The 215 SwitchTip has a 0.015 inch orifice and produces a 4 to 6 inch fan. Reverse the SwitchTip to easily clear clogs. Used for residential, commerical or industrial applicaitions. Best used with materials ranging from lacquers, latex paints and mastics.
Is spray painting walls easy?
Using a powered paint sprayer is a quick and efficient way to paint a room. The preparation time might feel longer, but the short time it takes to apply the paint quickly makes up for this.
What size tips for spraying acrylic paint?
A small tip (0.15mm) is best suited for fine-line work. In contrast, primers are best applied using a 0.4mm tip. Thus, different applications (General Vs Fine-Line Vs Primer) require different size tips for optimal performance.
What is size tip for latex paint?
Stain or lacquer: .009″ -.013″
What size tip do you use to spray polyurethane?
A tip that sprays between 1″-6″ wide is ideal for spraying polyurethane and other finishes. Most airless sprayers will come with a few selections, otherwise extra tips and be found at hardware stores and online. Next, you will need to adjust the volume control knob.
How do you Prime an airless paint sprayer?
Place the smaller prime tube in a waste pail and the suction tube in the bucket of strained paint. Turn the prime/spray valve to “prime.” Switch on the pump. Turn the pressure valve up until the pump starts. When the paint starts flowing from the prime tube, move it into the paint bucket.