Are there different size strike plates?
We stock 6 different widths and 6 finishes. Strike plate width is measured from center of screw holes to leading edge of strike plate.
What size is a standard strike plate?
A ANSI strike plate reinforces locks and deters tampering or kick-ins. Includes metal and wood screws. Size 4-7/8″ x 1-1/4″ in. …
What is the purpose of a strike plate?
The strike plate protects the jamb against friction from the bolt and increases security in the case of a jamb made of a softer material (such as wood) than the strike plate.
What is a deadbolt strike plate?
A strike plate or “Strike” is a metal plate that is secured to the door jamb for the purpose of reinforcing the latch on the lockset or deadbolt. They are an absolutely critical part of the security of any mechanical locking device, deadbolt or door knob.
What is an ASA strike plate?
The term “ASA” is still used by some commercial door manufacturers as follows: ASA: The designation for the 4 7/8˝ high strike with lip (per ANSI A115. 2) with the centerline of the strike located @ 40 5/16” above the bottom of the frame.
What is full lip strike?
Full Lip Strike: The full lip strike is the most common. As you can see there are 2 different kinds of full lip strikes: round corner or square. The measurement that this strike plate is showing would be considered the width, because it would be the width if it was on the door jamb.
What is the thing called that the door latch goes into?
The Bolt: Also called the latch, the bolt engages the inside of the door. There is a piece of metal that extends from the door into the frame itself. This bolt is used to hold it closed. The Box:The bolt extends from the cylinder into a hole that is designed to fit the bolt perfectly.
What is the hole in the strike plate called?
Box & Strike Plate The bolt extends from the cylinder into a small square shaped hole—this is the “box”. It is designed to hold the bolt securely in the doorframe when the lock is engaged.
Do you need strike plate?
Strike Plate This is the plate the latch-tongue, or deadbolt-tongue will connect with. It should sit flush with the door jamb. Any passage or privacy set needs to have a strike plate for the door to latch. Additionally, deadbolts need a strike plate to properly lock.
What does lockset bore mean?
The latch bore, also known as the edge bore, is the hole drilled from the side of the door into the cross bore to allow the latch of the lock to be installed and to accommodate the sliding of the deadbolt. The diameter of the latch bore is generally 1” to accommodate bolts from either mechanical or electronic locksets.
How do you make a strike plate hole deeper?
This can be corrected by enlarging the bolt pocket or changing the strike plate. To make the bolt pocket deeper, taller or wider, depending on where your bolt is dragging, use a chisel on the bolt hole until it is 1” deep and allows the bolt to fully extend without dragging.
What is Gator strike plate?
The GATOR Strike Plates is a new strike plate design anyone can install. It restores and improves door latch function lost due to house settling, door warping, hardware replacement, weather stripping, seasonal temperature variation, and added towel hooks and other door mounted accessories.
What is a security strike plate?
Security strike plates are larger and thicker than traditional strike plates and are designed to provide additional reinforcement around the extended latch or deadbolt on the jamb side of the entryway. Security strikes can also be surface mounted in order to shrink the gap between the door and the jamb.
What are magnetic plates?
Plate Magnets. The plate magnets can be used in a wide range of industries and are commonly installed within a chute or over a conveyor. The Mastermag range of plate magnets are constructed from a magnetic stainless steel casing, which utilises projected magnetic stainless steel poles for an enhanced field intensity.
What is magnetic sine plate?
There are two important variations of this tool. A magnetic sine plate uses magnets to more effectively hold pieces steady, from thin sheets to large work pieces. Compound sine plates are used to set compound angles for complex designs that require angles in multiple planes.