Do drop spindles lower your car?
Install our drop spindles to get your truck lower without loosing ride quality, plus you can maintain steering geometry! Drop-spindles relocate the shaft to a higher position, typically 2-3 inches higher than the original. Doing this allows your wheel to be higher in the fender well, thus lowering your truck.
Do you need drop shocks with drop spindles?
No. You do not need to use a drop shock when using 2” drop spindles because the spindle shaft and the pickup points for the caliper have been moved up. A stock or aftermarket lowering spring makes for a shorter height and therefore you need a shorter compression on the shock. …
What is a drop spindle on a car?
What is a Drop Spindle? A drop spindle merely replaces your stock ride-height spindle with one that relocates the shaft to a higher position (typically 2 to 3 inches) than the original, thus dropping ride height the corresponding amount.
Is it better to lower with springs or spindles?
The advantage of going with dropped spindles is stock springs and shocks can be used. Dropped spindles will lower the ride height yet maintain normal suspension clearances. The draw back is cost and additional labor.
Are drop spindles good?
Why is a drop spindle a better choice than using a drop spring? A. By using a drop spindle you will be maintaining a factory ride quality. Lowering springs are usually rated higher than stock springs depending on the amount of drop, taking away from the factory ride.
What is better drop spindles or lowering springs?
Will lowering shocks lower truck?
A lowered shock absorber is shorter than stock. It’s designed so that when it’s paired with a lowering spring it will have a full range of travel for that particular suspension. Your shock won’t be able to bottom out the same way, because it’s made to work with that kind of setup.
How do you know if you have drop spindles?
If the spindle snout is near the bottom ball joint tang, then it’s a stock spindle. If the snout is about mid-way between both upper and lower ball joint tangs then it’s a drop spindle.
How do you measure drop spindles?
In order to correctly take this measurement you will need to measure from the center of the spindle to the center of the main axle tube.
Do drop spindles affect ride quality?
Drop spindles are probably one of the best ways to lower your vehicle properly by two or three inches without affecting the ride quality or factory suspension geometry. Combining drop spindles with a two-inch lowering coil can give you up to four inches of drop.
What are 2 inch drop spindles?
2″ DROPPED SPINDLES (SP-101-K) Easily lower the height of your car or truck while keeping the suspension geometry in place for a smooth ride without the worry of added bump steer. Heidts drop spindles will work with most Mustang II kits including stock Mustang II factory suspensions.
How do you lower the front of a Chevy Silverado?
Figure 1. A lowered Silverado. Options to lower the front of your Silverado include drop spindles and new coil springs. To lower the rear, your options include axle flip kits, shackle and hanger kits, as well as torsion keys. For kits that provide drops of greater than two inches, shocks are generally included.
What type of drop spindles do you use for suspension?
McGaughys Suspension bolt-on drop spindles work well with factory components, and contain everything that is needed for your install, offering a 2″ to 2.5” drop in the front. McGaughys classic drop spindles are CNC machined from 60-grade ductile.
Who makes drop spindles for GMC?
McGaughys makes drop spindles for most of the popular car, truck & SUV models from Chevy, GMC, Dodge, Cadillac, Buick, Hummer, Oldsmobile, Pontiac and Toyota. Click below to find the right McGaughys Suspension drop spindles for your vehicle!
Why choose mcgaughys suspension drop spindles?
McGaughys drop spindles are designed, built, machined & cast in the USA using only the finest quality materials. McGaughys Suspension bolt-on drop spindles work well with factory components, and contain everything that is needed for your install, offering a 2″ to 2.5” drop in the front.