How do I enable Xdebug?

How do I enable Xdebug?

3 Answers

1. Download the latest version here.
2. Unpack the downloaded file with tar -xvzf xdebug-2.2.1.tgz.
3. Run cd xdebug-2.2.1.
4. Run phpize.
5. Run ./configure.
6. Run make.
7. Run sudo cp modules/xdebug.so /usr/lib/php/extensions/no-debug-non-zts-20090626.
8. Restart the web server with sudo apachectl restart.

Where is Xdebug config file?

First you need to find the location of the xdebug.so file on your server. Copy the location somewhere as you will use it later on. Now you need to navigate inside your server to a location: /etc/php5/apache2/conf. d/ and check if the file 20-xdebug.

What is Xdebug port?

By default, Xdebug 2 listens on port 9000. For Xdebug 3, the default port has changed from 9000 to 9003. You can specify several ports by separating them with a comma. By default, the Debug port value is set to 9001,9003 to have PhpStorm listen on both ports simultaneously.

What is Xdebug Client_host?

client_host = localhost # Configures the IP address or hostname where Xdebug will attempt to connect to when initiating a debugging connection. This address should be the address of the machine where your IDE or debugging client is listening for incoming debugging connections.

How do I know if xdebug is enabled?

Given that, you can confirm that xDebug is installed and in place by trying the following: 1) phpinfo() — this will show you all the extensions that are loaded, including xDebug. If it is there, then it’s a safe bet that it’s working. 2) If that isn’t good enough for you, you can try using the var_dump() function.

How do I know what version of xdebug I have?

You can check whether it did by running php -v . If Xdebug shows up with a version number, than you’re all set and you can configure Xdebug’s other functions, such as Step Debugging, or Profiling. If pecl did not add the right line, skip to the Configure PHP section.

How do I know if Xdebug is installed?

Given that, you can confirm that xDebug is installed and in place by trying the following:

1. phpinfo() — this will show you all the extensions that are loaded, including xDebug.
2. If that isn’t good enough for you, you can try using the var_dump() function.
3. xDebug modifies PHP’s error output.

How do I know what version of Xdebug I have?

How do I use xdebug on a remote server?

Steps (remote server):

1. Install Xdebug in your server: scl enable rh-php70 bash pecl install Xdebug.
2. Xdebug will need a port (usually its port 9000).
3. Edit a pool you wish Xdebug will run: vi /etc/opt/rh/rh-php70/php-fpm.d/www.conf.
4. Restart the PHP-FPM service: systemctl restart rh-php70-php-fpm.

What is Xdebug used for?

1, Xdebug is a debugging and profiling tool for use on development servers. By providing stack and function execution traces and error messages, Xdebug allows fatal errors to be debugged with the same clarity available during normal program execution without the limitation of the shutdown processes.

How do I know what version of xdebug I have Mac?

Open the file with a browser, you should now see a lot of information about the PHP version you are currently using. Search ( CMD + F ) for “xdebug” within the page. If you find it this means the module has been installed and is being used.

Do I have xdebug installed?

How do I get NetBeans to work with Xdebug?

Assuming you’ve downloaded and installed NetBeans, here’s how to get it to work with XDEBUG: Modify your php.ini file. Start by commenting out anything that refers to ZEND… by adding a semi-colon in front (to the left) of the line. Zend is not compatible with XDEBUG.

How do I install Xdebug IDE?

The IDE is assumed to be NetBeans. Download & installation of Xdebug is done by the following command: To “tell” your Apache web server about it, append to /etc/php5/apache2/php.ini file (this location may vary under other distributions) the following lines:

How do I enable debug mode in NetBeans?

Open your project in NetBeans. If you don’t have one yet, create one. Click Tools > Options > PHP. Debugger port: 9000. None of the checkboxes are checked. Click OK. Click File > Project Properties > Run Configuration > Advanced button.

Why doesn’t Xdebug have the tool tip in the CLI version?

1 in the CLI version of PHP it will not have the tool tip, nor in output files. This setting, defaulting to 0, controls whether Xdebug should write the return value of function calls to the trace files. For computerized trace files (xdebug.trace_format=1) this only works from Xdebug 2.3 onwards.