How much horsepower does a b18 Type R have?
The Integra Type R is equipped with a 1.8-liter DOHC VTEC in-line 4-cylinder (B18C) engine. In the JDM Type R this engine produces 200 PS (197 hp; 147 kW) at 8,000 rpm, whereas in the US models it produces 195 hp (198 PS; 145 kW) at 8,000 rpm and 130 lb⋅ft (176 N⋅m) of torque at 5,700 rpm.
Is b18b VTEC?
b18b is non-vtec and only appeared in the GSI integra. Both make roughly the same torque but vti-r revs higher and makes more horse power.
What is a LS VTEC swap?
An LS/VTEC motor combines the bottom end of a non-VTEC b-series motor with a DOHC VTEC head. When using the bottom end from a b20 CRV motor, you get both the torque of a larger motor with the high-end power of a b18c. When properly built, this engine will be as reliable as any other b-series motor.
Can I put a VTEC head on a non-VTEC engine?
Yes, as long as the engines are the same series, they should be interchangeable. The engine blocks, pistons, and crankshafts for all of the Accord/Prelude/Odyssey/CL F22Ax/F22Bx engines are basically identical, and the heads for any of them will bolt down and operate normally with any of the blocks.
How much horsepower can a stock B18B1 handle?
Just go with forged internals. Properly tuned, stock sleeves can handle 500 whp.
What is a B18B1 block made of?
yes, both block and head are cast aluminum. i noticed both of the people that have it wrong have b18b’s in their car… did it occur to you to go outside and look? iron and aluminum look very different.
What Hondas came with B18?
The B18 Family The B18 came in both non-VTEC and VTEC variations. The B18A non-VTEC powerplant was first seen in the 1986–1989 Accord Aerodeck, EXL-S/EX-S, and Vigor MXL-S in Japan. It was a 1.8L that made 160 hp and 128 ft-lbs of torque with dual Keihin carburetors.
How much horsepower can a stock b18b1 handle?
How do I install an obd1-obd2 engine in my 4th generation Civic/CRX?
To install an OBD1-OBD2 engine into your 4th Generation Civic/CRX the following adjustments will need to be made. First, if your car has dual point injection a conversion will need to be made to port injection. All Integra’s 1994 and up and Civic’s 1992 and up all use hydraulic transmissions.
What’s the difference between the B16A2/3 and B18B?
1. B16A2/3: Completely bolt-in Swap, VTEC needs to be wired, SIR II, Hasport shift linkage. Del Sol VTEC for the del sol 2. B18B: Completely bolt-in swap, SIR II, Hasport shift linkage. Del Sol VTEC for the del sol 3.
How do I swap a B-series transmission for an Integra transmission?
To complete the swap a B-series cable transmission will need to be used or a cable-hydro transmission conversion will need to be made. The left side bracket needs to be changed to a 1990-1993 Integra bracket. For the ECU, it is best to use the ECU which belongs with the engine.
Can a 4th Gen civic transmission be used in an Integra?
All Integra’s 1994 and up and Civic’s 1992 and up all use hydraulic transmissions. Therefore its not compatible with 4th Gen Civic’s because these vehicles have cable transmissions. To complete the swap a B-series cable transmission will need to be used or a cable-hydro transmission conversion will need to be made.